Isotherm Fridges
What are the voltage requirements for Isotherm products?
- Isotherm AC/DC products work on all power sources used worldwide including 12 and 24 volts DC as well as all AC voltages ranging from 80 to 260 volts including 115 volt and 220 volts both 50 and 60 Hertz.
- The electronic unit must always be connected directly to the battery or the main switch. Don’t mix up plus and minus. It is very important that cables of correct dimensions are used for the power supply.
Wire Dimension (mm²) Length (meter)
2.05 0 - 2.5
4 2.5 - 6
6 6 - 10
- Use a 20 amp DC breaker so power to the fridge can be turned off at the breaker rather than using the thermostat to turn off the fridge.
- Remember that the Danfoss electronics are designed to shut off when voltage drops below 11 volts. This will save batteries and allow critical systems like bilge pumps to continue working.
What is the power consumption of the refrigerator?
This is undoubtedly the most frequently asked question!
For Isotherm Cruise refrigerators we can provide accurate data about energy consumption as with all tests made we know their actual consumption. It 's more difficult to provide a figure for our refrigerating units systems because we do not know the actual size of the compartment in which it will be installed and also the thickness of the insulating material used. The data for a particular volume are therefore calculated with an insulating material of medium quality and thickness.
Which is the refrigerator more suitable to my needs?
Indel Webasto Marine has a large number of models, front opened, drawers, top-opened, stainless steel doors or customizable door fronts with different door panels. They can be right hinged or left hinged. In order to decide which is the best solution for your need, just measure the space for installation and thanks to the catalogue it will be extremely easy to search for the appropriate product.
Which power supplies are available?
The Isotherm refrigerators are available with standard 12V/24V power, on demand with AC / DC (12-24/115-230V).
Can I install the refrigerator in a position and the compressor unit in another one?
The refrigerators can be ordered with the compressor unit remotely positioned for separate installation of the refrigerator where space does not permit a standard installation.
I would like to build a cooling box on my boat, is it possible?
We can provide a set of panels ready to help you building a cooling box. The panels are covered on both sides with 2mm laminated plastic and have an overall thickness of 50mm closed cells foam insulation. They are extremely easy to cut and paste, using a polyurethane or silicone sealant.
Which model should I choose?
Indel Webasto Marine offers the most efficient refrigeration for boats thanks to special refrigerating units. Several types are available:
Compact Unit: The classical cooling unit, controlled by the thermostat, uses a Danfoss compressor to cool the evaporator installed in your refrigerator or freezer compartment. This system uses a condenser cooled by a fan. It is important that the compartment where the compressor is installed is well ventilated so that the cool air arrives at the bottom and warm air is exhausted to the top.
ASU Unit: The smart fridge that freezes the holding plate when the engine is running. The ASU system (which stands for AUTOMATIC START UP), runs the compressor when the engine is running and there is a considerable amount of electricity to freeze the holding plate, which consequently will maintain the temperature in the cockpit for extremely long periods also when the engine is not in use.
SP Unit: Isotherm SP (Self - Pumping) is a system directly cooled by sea water, this means that the efficiency of refrigeration is completely independent of the temperature inside the boat. The heat is directed downwards and expelled through the hull of the boat using the natural pumping action of the drain pipe of the galley sink through a heat sink installed on the discharge. This system is extremely quiet as no pumps nor cooling fans are present.
Magnum Unit: Magnum units are specially designed for boats that require maximum cooling, possibly to extend sailing in tropical waters. This system uses sea water, which is always cooler than the air inside the boat, through an electric water pump, increasing the cooling efficiency power. Sea water cooling system, being static, is absolutely noiseless, it resists even in the absence of water and is self-aerating.
What is the difference in ASU refrigerators and regular refrigerators?
While all Isotherm products are designed to consume a minimum of battery power, ASU products incorporate a small holding plate suspended under the freezer that acts like an artificial block of ice which keeps the compressor from running as often. The ASU technology monitors available amperage and will Automatically Start Up the 3 speed compressor and run it at high speed when there is additional amperage or at slow speed if there is not.
Isotherm has so many cabinet style refrigerator and freezer models – what do I need to know when ordering?
Isotherm cabinet style fridges give boat owners a full range of choices for selecting a refrigerator or freezer. Isotherm features three door styles:
Standard (black door and flange with a black panel that can be changed to your own custom panel or available white, teak, mahogany, or cherry panels),
Stainless Steel (complete stainless steel door, handle and flange)
Glass Line (white, black or blue tempered safety glass)
Be sure to specify hinges on right or hinges on left.
What should be done if you go on holiday?
As you sail for several days, it is good practice to clean the refrigerator and check you do not have food with a short time sell-by date that could deteriorate and cause bad odours. It is also suggested to set the thermostat to minimum. In this way, while guaranteeing the preservation of frozen food, you also reduce power consumption.
How can I get rid of unpleasant odours in my refrigerator?
Clean the inside with a mild detergent.
What are the climate classes?
All refrigerators are equipped with climate class that indicates the temperature within which an appliance is working properly. The following climatic classes: Class SN +10 ° C +32 ° C and Class N between +16 ° C and +32 ° C Class ST between +18 ° C and +38 ° C Class T between +18 ° C and +43 ° C
What should I consider when installing my new fridge?
- The weight of the fridge must be supported on the feet of the refrigerator. The flange is designed to hold the fridge in the enclosure.
- Good ventilation is the key to efficient operation and good temperatures. Allow 12 x 12 centimetres at the bottom of the cabinet and another 12 x 12 centimetres at the top to allow warm air to rise up and out of the cabinet while allowing cool air to enter at the bottom.
- Good power with no drop in voltage or amperage.
How long should I wait before starting a refrigerator that has just been moved? In order to avoid damage to the cooling circuit, we suggest you waiting about 2 / 3 hours prior to ignition of the product.
Why is Isotherm so much better than other refrigerators?
- Isotherm features molded door shelves that are an integrated part of the door, providing strength and stability for doors.
- Isotherm has cradles and adjustable holders that keep jars and bottles secure and upright.
- Isotherm has a one-piece, polished food-grade plastic interior that helps resist odors.
- Isotherm has positive latching doors that stay shut even in the roughest conditions.
- Isotherm has the highest level of quality and elegance that adds value to every installation.
Isotemp WATER HEATERS
Why should I choose Isotemp Water Heaters?
Isotemp Slim and Basic water heaters are ranges of water heaters from 15 to 75L volumes, made just for marine use.
They give you the following advantages:
- Robust design
- Horizontal or vertical mounting options
- Water tank in stainless steel, corrosion resistant
- External cylinder in stainless steel
- Stable fixing feet in stainless steel, adjustable to 360 degrees for easy installation
- Warranty up to 5 years
- Extra-long corrugated heating coil for high heat exchange efficiency
- Special safety valve 7bar/100psi
- Ultra-thick insulation for lowest temperature loss
- Electrical plug and play
- Immersion heating element, especially designed to heat also the water at the bottom of the tank
- Thermostat mixing valve for mixing hot and cold water (optional)
I would like to purchase a water heater, which model? Which power supply?
You can choose among several models with different capacities: 15L, 16L, 24L, 25L, 30L, 40L, 50L, 75L.
Power installed: 115V or 230V
Immersion heating element available on:
- 750W
- 800W
- 1000W
- 2000W
- 3000W
Why should I select a water heater with a bigger resistance/heating element?
Obviously the higher the power of resistance, the less the water heater will remain in operation; absorption is higher and therefore the consumption accordingly.
Why should I choose a double coil water heater?
A double coil water heater can be connected to an additional heating system as our air-heater and it is therefore the ideal choice for those who want to run a single product with two separate systems. The air-heater is used to heat small rooms or defrost the windows and then the heating power is not very high but it certainly helps to do more things and save energy on board.
